Home > Certificate > Automotive Mechanic > Frankston > Certificate III in Automotive Mechanical Technology (Mechanical - Light Vehicle) - Frankston - Victoria

Certificate III in Automotive Mechanical Technology (Mechanical - Light Vehicle)

Speak without obligation to Chisholm Institute of TAFE Frankston Campus

To contact you must accept the privacy policy

Comments about Certificate III in Automotive Mechanical Technology (Mechanical - Light Vehicle) - On Campus - Frankston - Victoria

  • Objectives
    This is a fully accredited course for new employees entering the Motor Mechanic industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based apprenticeship course that is delivered as a combination of formal off the job training at Chisholm and on the job work experience and informal training in the workplace.
  • Academic Title
    Certificate III in Automotive Mechanical Technology (Mechanical - Light Vehicle)
  • Course description
    WHAT IS AN APPRENTICESHIP?
    Apprenticeships are normally a four year package that consists of employment and training. An apprentice attends Trade School for up to three years on a part time basis but also receives training on-the-job. There are special government subsidies and rates of pay and conditions for apprentices.

    Apprentices must be fifteen years of age or over and must have a registered/licensed employer who has agreed to employ them as an apprentice. Apprenticeships are for new employees or
    employees that have been employed for less than three months on a full time basis or 12 months on a part time basis.

    WHAT IS CERTIFICATE III IN AUTOMOTIVE (MECHANICAL-LIGHT VEHICLE)?
    This is a fully accredited course for new employees entering the Motor Mechanic industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based assessment course that is primarily delivered in the workplace.
    This course is offered at both Dandenong and Frankston campuses and will take up to three years of part time study, (block release) to complete.

    WHAT ARE THE COURSE ENTRY REQUIREMENTS?
    There are no formal requirements for entry into this course other than to have entered into a ‘Contract of Training’ with your employer and be employed as an apprentice.

    EMPLOYMENT OPPORTUNITIES
    Motor Mechanic

    WHERE CAN I GET FURTHER INFORMATION?
    Dandenong Campus

    STUDY AREAS
    AURC270103A Apply Safe Working Conditions 20
    AURE218676A Test, Service and Charge Batteries 15
    AURE218708A Carry Out Repairs to Single Elect Circ. 40
    AURE319166A Repair Charging Systems 30
    AURE319266A Repair Starting Systems 30
    AURE320666A Repair Ignition Systems 30
    AURE321171A Service & Rep Electronic Engine Mgt 60
    AURE321271A Service & Rep. Electronic Drive Mgt 50
    AURE321371A Service & Rep. Electronic Body Mgt 40
    AURT200108A Carry Out Servicing Operations 20
    AURT201170A Inspect & Service Engines 20
    AURT202166A Repair Cooling Systems 20
    AURT203670A Service Diesel Fuel Inject. Systems 20
    AURT207170A Service Auto Transmission 10
    AURT217108A Carry Out Wheel Alignment Op. 40
    AURT217606A Balance Wheels & Tyres 10
    AURT222670A Service Air Conditioning 20
    AURT270278A Use & Maintain W/place Tools & Equip 40
    AURT271781A Apply Environmental Regulations 20
    AURT301166A Rep Engines & Assoc. Eng. Comps 40
    AURT303166A Repair Petrol 40
    AURT304270A Service LPG Fuel Systems 15
    AURT304666A Rep & Replace Emission Control Sys 20
    AURT306170A Inspect, Service +/or Repair Clutch Assemble. & Assoc. Operating Systems Components 30
    AURT306666A Repair Manual Transmission 40
    AURT307166a Repair Auto Transmission 50
    AURT310166A Repair Hydraulic Braking Systems 40
    AURT312666A Repair Final Drive (Assemblies) 20
    AURT313166A Repair Final Drive (Driveline) 20
    AURT315166A Repair Steering Systems 30
    AURT316166A Repair Suspension Systems 30
    AURT365130A Inspect Vehicle Systems 20
    AURT365508A Safety/Roadworthy Inspection 10
    AURT366108A Carry Out Diagnostic Procedures 20
    MEM5.4AB Perform Routine Oxy Acetylene Weld 20
    MEM5.7AB Manual Heating & Thermal Cutting 20

    ALSO
    The Institute has:
    • A bookshop to cater for all your textbook and
    stationery needs;
    • Car parking on campus;
    • On campus canteen that is open in the evening during
    school terms

Other programs related to Automotive Mechanic

This site uses cookies. If you continue navigating, the use of cookies is deemed to be accepted. See more  |