Home > Certificate > Automotive Mechanic > Frankston > Certificate III in Automotive Specialist (Auto Forklift Mechanic) - Frankston - Victoria

Certificate III in Automotive Specialist (Auto Forklift Mechanic)

Speak without obligation to Chisholm Institute of TAFE Frankston Campus

To contact you must accept the privacy policy

Comments about Certificate III in Automotive Specialist (Auto Forklift Mechanic) - On Campus - Frankston - Victoria

  • Objectives
    This is a fully accredited course for new employees entering the trade as a Forklift Truck Mechanic or current employees wishing to gain a formal qualification for their existing skills. This is a competency based apprenticeship course that is delivered as a combination of formal off the job training at Chisholm and on the job work experience and informal training in the workplace.
  • Academic Title
    Certificate III in Automotive Specialist (Auto Forklift Mechanic)
  • Course description
    WHAT IS AN APPRENTICESHIP?
    Apprenticeships are normally a four year package that consists of employment and training. An apprentice attends Trade School for up to three years on a part time basis but also receives training on-the-job. There are special government subsidies and rates of pay and conditions for
    apprentices. Apprentices must be fifteen years of age or over and must have a registered/licensed employee who has agreed to employ them as an apprentice. Apprenticeships are for new
    employees or employees that have been employed for less than three months on a full time basis or 12 months on a part time basis.

    WHAT IS CERTIFICATE III IN AUTOMOTIVE HEAVY STREAM – Auto Forklift Mechanic?
    This is a fully accredited course for new employees entering the Motor Mechanic (Auto Forklift) industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based assessment course that is primarily delivered in the workplace.
    This course is offered at Frankston campus and will take up to three year of part time study, block release (approx. 1124 hours) to complete.

    WHAT ARE THE COURSE ENTRY REQUIREMENTS?
    There are no formal requirements for entry into this course other than to have entered into a ‘Contract of Training’ with your employer and be employed as an apprentice.

    EMPLOYMENT OPPORTUNITIES
    Motor Mechanic (Auto Forklift)

    WHERE CAN I GET FURTHER INFORMATION?
    Frankston Campus

    STUDY AREAS
    Module Code Module title Hours
    Compulsory
    AURC270103A Apply safe working practices 20
    AURT271781A Imp & monitor environ regs in Auto 20
    AURT409166A Repair hydraulic systems 60
    AURT366108A Carry out diagnostic procedures 20
    AURT300771A Service & repair lift truck mast 10
    AURT309131A Install hydraulic system to spec apps 74

    Electives
    AURC270789A Comm effectively in the Workplace 20
    AURE218676A Test, service and charge battery 15
    AURT200108A Carry out service operations 20
    AURV281208A Carry out brazing procedures 30
    AURT201170A Inspect and service engines 20
    AURT203170A Service petrol fuel systems 15
    AURT203670A Service diesel fuel injection sys. 20
    AURT207170A Inspect & service transmission (Auto) 10
    AURT209170A Service hydraulic systems 20
    AURT270278A Use & maintain W’place tool & equip 20
    AURT304270A Service LPG fuel systems 15
    AURT305671A Inspect & repair engine forced ind. 15
    AURE218708A Carry out repairs single elect circ. 40
    AURE318866A Repair electrical systems 80
    AURT310166A Repair hydraulic break systems 40
    AURE319166A Repair charging systems 30
    AURE319266A Repair starting systems 30
    AURT202166A Repair cooling systems 20
    AURT303666A Repair diesel fuel systems 80
    AURT301166A Repair engine and systems 60
    AURE321171A Service/Repair elect spark ignition 50
    AURT307166A Repair transmission (auto) 50
    AURE320666A Repair ignition systems 30
    AURT304266A Repair LPG fuel systems 40
    AURT306170A Inspect, service &/or repair clutch 30
    AURT308166A Repair transmissions (hydrostatic) 40
    AURT312666A Repair final drive assemblies 20
    MEM05007C Perf man heating & thermal cutting 20
    MEM05017C Weld using gas metal arc welding 40

    Total hours 1124

    ALSO
    The Institute has:
    • A bookshop to cater for all your textbook and stationary
    needs;
    • Car parking on campus;
    • On campus canteen that is open in the evening during
    school terms

Other programs related to Automotive Mechanic

This site uses cookies. If you continue navigating, the use of cookies is deemed to be accepted. See more  |