Home > Certificate > Automotive Mechanic > Frankston > Certificate III in Automotive Specialist (Diesel Fitter) - Frankston - Victoria

Certificate III in Automotive Specialist (Diesel Fitter)

Speak without obligation to Chisholm Institute of TAFE Frankston Campus

To contact you must accept the privacy policy

Comments about Certificate III in Automotive Specialist (Diesel Fitter) - On Campus - Frankston - Victoria

  • Objectives
    This is a fully accredited course for new employees entering the Motor Mechanic (Diesel Fitter) industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based apprenticeship course that is delivered as a combination of formal off the job training at Chisholm and on the job work experience and informal training in the workplace.
  • Academic Title
    Certificate III in Automotive Specialist (Diesel Fitter)
  • Course description
    WHAT IS AN APPRENTICESHIP?
    Apprenticeships are normally a four year package that consists of employment and training. An apprentice attends Trade School for up to three years on a part time basis but also receives training on-the-job. There are special government subsidies and rates of pay and conditions for
    apprentices.

    Apprentices must be fifteen years of age or over and must have a registered/licensed employee who has agreed to employ them as an apprentice. Apprenticeships are for new employees or employees that have been employed for less than three months on a full time basis or 12 months on a part time basis.

    WHAT IS CERTIFICATE III IN AUTOMOTIVE HEAVY STREAM – DIESEL FITTER?
    This is a fully accredited course for new employees entering the Motor Mechanic (Diesel Fitter) industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based assessment course that is primarily delivered in the
    workplace. This course is offered at Frankston campus and will take up to three year of part time study, block release (approx. 1055 hours) to complete.

    WHAT ARE THE COURSE ENTRY REQUIREMENTS?
    There are no formal requirements for entry into this course other than to have entered into a ‘Contract of Training’ with your employer and be employed as an apprentice.

    EMPLOYMENT OPPORTUNITIES
    Motor Mechanic (Heavy Stream - Diesel)

    WHERE CAN I GET FURTHER INFORMATION?
    Frankston Campus

    STUDY AREAS
    AURC270103A Apply Safe Work Practice
    AURT270278A Use & Maintain Tool/Equipment
    AURT200108A Carry Out Servicing Operations
    AURT201170A Inspect/Service Engine Systems
    AURT203670A Service Diesel Fuel Injection Systems
    AURT271781A Imp/Monitor Environment Regs In Auto
    AURT209170A Service Hydraulic Systems
    AURT206670A Inspect/Service Manual Transmission
    AURE218676A Test/Service Charge Batteries
    AURT304666A Remove and Replace Emission Controls
    AURT305671A Inspect & Repair Engine Forced Induction
    AURT201164A Remove and Install Engine Assemblies
    AURT207170A Inspect & Serv. Automatic Transmission
    AURT225156A Read & Interpret Engineering Drawings
    AURC270789A Communicate Effectively In the Workplace
    AURE218708A Carry Out Repairs Single Elect Circ.
    AURT306170A Inspect, Service &/or Repair Clutch Systems
    AURT409166A Repair Hydraulic Systems
    AURE319166A Repair Charging Systems
    AURE319266A Repair Starting Systems
    AURT202166A Repair Cooing Systems
    AURT307166A Repair Automatic Transmission
    AURE318866A Repair Electrical Systems
    AURT303666A Repair Diesel Fuel Systems
    AURT301166A Repair Engine and Systems
    AURE321771A Service/Repair Electronic Engine Man.
    AURT366108A Carry out Diagnostic Procedures
    AURT403645A Overhaul Diesel Fuel Injection Systems
    AURV281208A Carry Out Brazing Procedures
    AURT125667A Use & Maintain Basic Measuring Devices
    MEM 5.17AB Gas/Metal Arc Welding
    MEM 5.7AB Manual Heating and Thermal Cutting

    ALSO
    The Institute has:
    • A bookshop to cater for all your textbook and stationery
    needs;
    • Car parking on campus;
    • On campus canteen that is open in the evening during
    school terms

Other programs related to Automotive Mechanic

This site uses cookies. If you continue navigating, the use of cookies is deemed to be accepted. See more  |