Home > Certificate > Automotive Industry, Car > Dandenong > Certificate III in Automotive (Vehicle Body - Panel Beating) - Dandenong - Victoria

Certificate III in Automotive (Vehicle Body - Panel Beating)

Speak without obligation to Chisholm Institute of TAFE Dandenong Campus

To contact you must accept the privacy policy

Comments about Certificate III in Automotive (Vehicle Body - Panel Beating) - On Campus - Dandenong - Victoria

  • Objectives
    This is an accredited course for new employees entering the Auto body Repair industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based apprenticeship course that is delivered as a combination of formal off the job training at Chisholm and on the job work experience and informal training in the workplace
  • Academic Title
    Certificate III in Automotive (Vehicle Body - Panel Beating)
  • Course description
    WHAT IS AN APPRENTICESHIP?
    Apprenticeships are normally a four year package that consists of employment and training. An apprentice attends Trade School for up to three years on a part time basis but also receives training on-the-job. There are special government subsidies and rates of pay and conditions for apprentices.

    Apprentices must be fifteen years of age or over and must have a registered/licensed employee who has agreed to employ them as an apprentice. Apprenticeships are for new employees or employees that have been employed for less than three months on a full time basis or 12 months on a part time basis.

    WHAT IS CERTIFICATE III IN AUTOMOTIVE (VEHICLE BODY – PANEL BEATING)?
    This is a fully accredited course for new employees entering the Auto body Repair industry or current employees wishing to gain a formal qualification for their existing skills. This is a competency based assessment course that is primarily delivered in the workplace.

    This course is offered at Dandenong campus and will take up to three years of part time study, block release (approx. 970 hours) to complete.

    WHAT ARE THE COURSE ENTRY REQUIREMENTS?
    There are no formal requirements for entry into this course other than to have entered into a ‘Contract of Training’ with your employer and be employed as an apprentice.

    EMPLOYMENT OPPORTUNITIES
    Panel Beater

    WHERE CAN I GET FURTHER INFORMATION?
    Dandenong Campus

    STUDY AREAS
    AURC270103A Apply Safe Working practice 20
    AURC270789A Comunt. Eff. in the Workplace 20
    AURE218676A Test, Service&Charge Batteries 15
    AURT270278A Use&Maintain Workplace Tools & Equipment 20
    AURV225908A Carry Out Panel Repairs 40
    AURV226864A Rmv,Rplc.&Realign Bolt-on 90
    AURV226965A Remove & Replace/Fit Protector Mouldings 15
    AURV230203A Apply Rust Prevention & Sound deadening 20
    AURV231649A Prep. Vehicle Compt./Equip.t for customer use 20
    AURV233363A Remove & Install Rubber-Glazed Windows 30
    AURV233563A Remove & Install Direct Urethane Glazed Windows 30
    AURV281508A Carry Out Spot Welding Procedures 20
    AURV323908A Carry Out Thermoplastic Welding Procedures 30
    AURV326266BA Rep. Bdy Panels (Metal Finishing) 35
    AURV326266CA Repair Bdy Panels (Incorp Filler) 35
    AURV326266AA Repair/Replace Structural Damage (Welding) 30
    AURV326367A Replace Major Welded Panels 50
    AURV326508A Rep. Veh. Body Misalignment 50
    AURV326708A Carry-out maj. Sectional Repair 80
    AURV326964A Rem.&Rep. Adhesive Bonded 40
    AURV327466AA Rep. Alum. Bdy Pnl (Finishing) 30
    AURV327466BA Rep. Alum. Bdy Pnl (By Filling) 30
    AURV365356A Read& Interp. Veh. Body Rep. Est./Quotations. 25
    AURV371481A Imp.& Mon Enviro. Regs & Best practice 20
    AURV465116A Determine Veh. Body Damage & Recommend Rep. Procedure 40
    MEM5.17AB Weld Using Gas Metal Arc, Mig Welding Process, Spot Welding 40
    MEM5.4AB Perf Routine Oxy Ace. Welding 20
    MEM5.7AB Manual heating & Thermal Cutting 20

    The Institute has:
    • A bookshop to cater for all your textbook and stationary
    needs;
    • Car parking on campus;
    • On campus canteen that is open in the evening during
    school terms

Other programs related to Automotive Industry, Car

This site uses cookies. If you continue navigating, the use of cookies is deemed to be accepted. See more  |